Dissipative Table/Floor Matting Rolls ESD Table Rubber Mat

• Customization: Available
• Certification: RoHS, ISO
• Color: Green, Blue, Gray, Black
• Model NO.: EM0101
• Usage: Cleanroom
• Construction Material: Rubber
• Normal Size: 0.6, 0.9, 1.0, 1.2m*10m*2mm and etc
• Two Layers: Static Dissipation Layer + Conductive Layer
• Surface: Shiny or Dull
• Remarks: Above Sizes Are Standard, Customized Size Availabl
• Condition: New
• Waterproof: Waterproof
• Type: Mat
• Material: Rubber
• Transport Package: 1 Roll/Box
• Specification: 0.6, 0.9, 1.0, 1.2M*10m*2mm
• Trademark: ALLESD
• Origin: Jiangsu, China
• HS Code: 40169100
• Production Capacity: 1000rolls/Week

Product Description

Method for laying dissipative table mat:
Lay the dissipative mat on the table, connect the button of the antistatic grounding line on the surface and connect the other end to the grounding conductor, to discharge the static electricity through the grounding wire.
1. The upper surface is to gather the static electricity around the table, with the resistance of 10e7 - 10e9 Ω Cm
2. The black bottom is a conductor ≤ 10e6 Ω Cm, to quickly discharge the gathered static electricity
3. The grounding wire is to connected with the dissipative mat and the other end to the ground, to smoothly discharge the static electricity through the wire.

Method for laying dissipative floor mat
1. Requirements on floor
A. The floor shall be the wet rubbing, ceramic or wooden floor;
B. It shall be flat, without obvious undulation, and with the roughness less than 2‰ ;
C. It shall be in enough strength, without sand streak or scaling.
D. The floor shall be dry.
2. Construction procedures and methods
A. Clean the floor with #120 gasoline or xylene (with cleaning machine);
B. Lay the copper bars or aluminum bars, when the copper bars are 0.02mm thick and 30mm wide, the length and number shall be subject to the actual requirements during laying, and lead one end of the copper bars to ground.
C. After laying the grounding grid, clean the dry floor, coat the conductive glue, and allow it to dry for 20`30 minutes until it is not sticky. Repeat the same procedures for the bottom of the antistatic floor mat (black), but coat the conductive glue once. Then bind the antistatic plastic on the floor, roll 5 times with heavy roller, to make it flat and smooth. Allow it to stay for 48 hours under normal temperature before use.
D. Construct under the ambient temperature not less than 25° C and the humidity not more than45%, and well ventilated.
E. Ensure the resistivity of conductive glue not more than 108Ω Cm, and the anti-stripping strength at Kg/2.5cm.
F. Coat the conductive glue or paste on the copper bar for conductivity in the gaps.

Applications:
It is used for workstation surface and provide a cushiony ESD surface that is resistant to heat and most of the chemicals.
It is ideal for use in setting up workstation in electronic assembly and electronic sensitive storage areas and advanced laboratories for microelectronic industries, protect electronic devices during production, storage and shipping.
 

Performance index of Dissipative Table/Floor Mat
Dissipative Table Mat/Floor Mat			Specification	Color
Static Dissipation layer	Surface resistance	10e7 -10e9	1.2mx*10mx*2mm(T) 1.0mx*10mx*2mm(T)	Green, blue,  gray
	Friction static potential V	<100
Conductive layer  (black bottom)	Surface resistance	≤10e6
	Friction static potential V	<60
Static voltage attenuation period	5000 - 500V	<1.9s
Flame retardation	GB4609-84, FV-0 (less than 10S)
Volume resistance	10e7 -10e10 Ωcm

 
Physical performance index of Dissipative Table/Floor Mat

No.	Description		Test reference	Results
1	Tensile strength		GB 1040	3.6Mpa
2	Fracture elongation		GB 1040	188%
3	Tear elongation		GB/T 529	20.6KN/m
4	Rebound elasticity (the specimen is laminated with 6 layers of sheets)		GB/T 1681	14%
5	Impact embrittlement temperature (no cut)		GB 5470	No damage
				at -25°C
6	Permanent compression change rate, 70°C*22h, compression 25%		GB 10654	17.90%
7	Hot air ageing	Tensile strength change rate	GB/T 7141	8.00%
		Fracture elongation change rate		-3.80%
		Weight loss on heating		1.08%
Remarks	Test according to national standards: GB 1040, GB/T 529, GB/T 1671, GB 5470, GB 10654 and GB/T 7141.

Our Service:
High-quality manufacturing
Nowadays,scientific technology leads the future, so fully and freely playing the technology is our dream, we choose the raw material carefully, control thr products strictly,make a thoughtful products transportation and delivery, we try to be the best.
Our company strictly follow ISO quality system and effectively controls every production line.
 
Quality control
The quality of survival, in order to adapt to the market development trend of internationalization of the economy,we expertise on product quality,management and efforts to do a comprehensive upgrade of the production quality of testing equipment, has played a full role in safeguarding the environment, let customers know the professional use of the product(safety,environmental protection.







FAQ:
Trade Terms:
1. Payment: T/T
2. Delivery Time: 1-2 weeks
 
Why Choose Us?
1. We are the leading manufacturer and exporter of various ESD & Clean room products.
2. Honest but competitive price and Quality assured quotation.
3. 100% QC inspection before shipment.